Scarifier Steel Cutters

 

Article Description Diamètre interne Diamètre externe Épaisseur Convient aux machines :
615.01.02
615.01.02 		Grand angle 16mm
(5/8")		 39.69mm
(1 9/16")		 3.17mm
(1/8" )		 FR200, SC8E, FS200
644.04.06
615.01.04 		Petit 16mm
(5/8")		 (1 5/8") 3.17mm
(1/8" )		 FR200, SC8E, FS200

615.01.04644.04.06 		Moyen 16mm
(5/8")		 52.39mm
(2 1/16")		 3.17mm
(1/8" )		 VA25S, SC10E, CPM10, SPS10

CHS.20.02 		Dent moyenne 16mm
(5/8" )		 50.8mm
(2")		 3.17mm
(1/8" )		 MEULE À CHARIOT
CHS.30.01
CHS.30.02		 Grande dent 30mm
(1 8/10")		 75mm
(2.95")		 5mm
(1/5" )		 MEULE À CHARIOT, VA30S, SC12E
CHS.30.01
CHS.30.01 		Grande dent 28.58mm
(1 1/8")		 76.2mm
(3")		 7.14mm
(9/32" )		 MEULE À CHARIOT, VA30S, SC12E

 

 

Scarifier Tungsten Cutters

 

Article Description Diamètre interne Diamètre externe Épaisseur Convient aux machines :
615.01.07
615.01.07 		Petit 5 pts 16mm
(5/8" )		 44.45mm
(1 ¾")		 6.5mm
(¼")
615.01.14
615.01.14 		Petit 6 pts 16mm
(5/8" )		 44.45mm (1 ¾" 6.5mm
(¼")		 FR200, SC8E, FS200, CPM8, SPS8
615.08.31
615.08.31 		Medium 8pt 51.59mm
(2 1/32" )		 56.37mm
(2 7/32" )		 6.5mm
(¼")		 VA25S, SC10E, CPM10, SPS10
615.08.30
615.08.30 		Medium 8pt (special order) 25.4mm
(1" )		 57.15mm
(2 ¼")		 6.5mm
(¼")		 AIRTEC 320
620.01.13
620.01.13 		Grand 8 pts 30.16mm
(1 3/16" )		 80.96mm
(3 3/16" )		 7.94mm
(5/16" )		 VA30S, SC12E
620.01.14
620.01.14 		Grand 12 pts 26.2mm
(1 1/32" )		 77.79mm
(3 1/16" )		 7.94mm
(5/16" )		 MEULE À CHARIOT
630.03.10
630.03.10 		Grand 12 pts 30.16mm
(1 3/16" )		 77.79mm
(3 1/16" )		 7.94mm
(5/16" )		 MEULE À CHARIOT
630.03.13
630.03.13 		Grand 12 pts 33.02mm
(1.30" ) 		77.79mm
(3 1/16" )		 7.94mm
(5/16" )		 MEULE À CHARIOT

 

 

Scarifier Milling Cutters

 

Article Description Diamètre interne Diamètre externe Épaisseur Convient aux machines :
615.01.11
615.01.11 		Petit 11.11mm
(7/16" )		 30.16
(1 3/16" )		 22.23mm
(7/8" )		 FR200, SC8E, FS200
644.01.13
644.01.13 		Moyen 18.26mm
(23/32" )		 57.15mm
(2 ¼")		 19.05mm
(¾")		 VA25S, SC10E, CPM8, CPM10, SPS10
630.03.08
630.03.08 		Grand 82.55mm
(3 ¼")		 82.55mm
(3 ¼")		 38.1mm
(1 ½")		 VA30S, SC12E
630.03.09
630.03.09 		Large étroit 82.55
(3 ¼")		 82.55mm
(3 ¼")		 19.05mm
(¾")		 MEULE À CHARIOT, VA30S, SC12E

 

 

Scarifier Parts

 

Article Description Convient aux machines :
SC.08.510 Flail Shaft, 12mm SC8E, FR200
SC.10.510 Arbre de fléau, 9/16" pour tambour ultra 4140 10 SC10E
633.04.02 Flail Shaft, 12mm VA25S
SC.08.401 Arbre, hexagonal SC8E
SC.10.401 Arbre, hexagonal SC10E
SC.12.500 Flail shaft, 20mm for 4 Shaft Drum SC12E, VA30S
SC.08.500 Drum w/o Cutters Sc8E, FR200
SC.08.901 Roue, avant SC8E, FR200
SC.10.901 Roue, avant SC10E, FR300, VA25S, VA30S
SC.10.121 Roue, arrière SC10E, FR300, VA25S, VA30S
SC.08.119 Courroie, dentée SC8, 640, FR200 gaz/élec
SC.10.117 Courroie, dentée SC10E, 880 gaz, VA25S
SC.12.117 Courroie, dentée SC12E gaz, 1040, VA30S
SC.10.156 Poulie, gaz dentée supérieure SC10E, FR250, FR350, VA25S
SC.08.203 Poulie, dentée inférieure SC8E, FR200
SC.10.505 Drum w/o cutters SC10E, VA25S
SC.10.404 Support, côté entraînement SC10E, VA25, VA25S, 6207-2Rs
SC.10.604 Support, plaque de fond SC10E, VA25, VA25S, 6207-2Rs
SC.08.404 Support, côté entraînement SC8E, FR200
SC.08.604 Support, plaque de fond SC8E, FR200, 6006-2Rs
SC.12.404 Support, côté entraînement SC12E, VA30, FR300, FR350, FR250T, 63072
SC.08.604 Support, plaque de fond SC8E, FR200, 6006-2Rs
SC.12.505 Drum w/o Cutters SC12E, VA30S
NB.70.111 Key, Woodruff for Hexagonal Shaft SC8E, FR200
NB.70.115 Key, Woodruff for Hexagonal Shaft SC10E, FR200
SC.12.401 Shaft, Hexagonal SC12E, VA30S
SC.12.407 Key, Woodruff for Hexagonal Shaft SC12E, VA30S
SC.08.803 Wheel, Rear SC8E, FR200
SC.08.803 Wheel, Rear SC10E, VA25S, SC12E, VA30S
SC.12.156 Pulley, Upper for gas models SC12E, VA30S
SC.10.403 Pulley, Lower SC10E, VA25S
SC.12.403 Pulley, Lower SC12E, VA30S
SC.12.121 Pulley, Tightening SC12E, VA30S
SC.12.808 Plate, Joint SC12E, VA30S
NB.20.112 Nut, Shaft SC8E, FR200
NB.30.218 Washer, Safety SC8E, FR200
SC.10.206 Guard, Belt SC8E, FR200
SC.12.118 Guard, Belt SC12E, VA30S